M25P16 DATASHEET PDF

Kak Attempts to write to the Status Register are rejected, and are not accepted for execution. No SPI device can operate correctly in the presence of excessive noise. Details of how to find the Technology Process in the marking are given datashest AN1see also Section S01 6 wide — 1 6-lead Plastic Small Outline, mils body width, mechanical data 51 Table Read Identification RDID instruction sequence and data-out sequence 0 1 2 3 4 5 6 datasbeet 8 9 10 11 12 13 14 15 16 17 18 28 29 30 31 anmuWuuuuuuuuuui. AC characteristics Grade 6. Instruction set 19 Table 5.

Author:Jutaur Dugul
Country:Serbia
Language:English (Spanish)
Genre:Finance
Published (Last):24 March 2016
Pages:261
PDF File Size:4.8 Mb
ePub File Size:8.81 Mb
ISBN:988-8-59601-827-2
Downloads:28611
Price:Free* [*Free Regsitration Required]
Uploader:Zologore



Ordering datashwet scheme Example: The parameters in the DC and AC Characteristic tables that follow are derived from tests performed under the Measurement Conditions summarized in the relevant tables. Logic diagram 6 Figure 2. At Power-up, the device is in the following state: The old-style Electronic Signature is supported for reasons of backward compatibility, only, and should not be used for new designs. When set to 1such a cycle is in progress, when reset to 0 no such cycle is in progress.

AC measurement conditions 38 Table Before this can be applied, the bytes of memory need to have been erased to all 1s FFh. D2 Max should not exceed D — K-2 x L. Chip Select S can be driven High at any time during data output. Each device in a system should have the V cc rail decoupled by a suitable capacitor close to the package pins. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied.

This is followed by the bit device identification, stored in the memory, being shifted out on Serial Data Output Qeach bit being shifted out during the falling edge of Serial Clock C. M52p16 modes supported 11 Figure 6. These parameters are characterized only. AC measurement conditions Symbol Parameter M25p1.

Then the memory contents, at that address, is shifted out on Serial Data Output Qeach bit being shifted out, at a maximum frequency f cduring the falling edge of Serial Clock C. Chip Select S must be driven High after the eighth bit of the last address byte has been latched in, otherwise the Sector Erase SE instruction is not executed.

Normal precautions must be taken for supply rail decoupling, to stabilize the V cc supply. However, taking this signal Low does not terminate any Write Status Register, Program or Erase cycle that is m25l16 in progress. After Power-up, a falling edge on Chip Select S is required prior to the start of any instruction. Once in the Stand-by Power mode, the device waits to be selected, so that it can receive, decode and execute instructions.

However, the correct operation of the device is not guaranteed if, by this time, V cc is still below V cc min. Values are latched on the rising edge of Serial Clock C. Normally, the device is kept selected, with Chip Select S driven Low, for the whole duration of the Hold condition. Published internally, only Jun 0. The device consumption drops to I CC1. The value of the 8-bit Electronic Signature, for the M25P1 6, is 1 4h. That is, Chip Select S must driven High when the number of clock pulses after Chip Select S being driven Low is an exact multiple of All attempts to access the memory array during a Write Status Register cycle, Program cycle or Erase cycle are ignored, and the internal Write Status Register cycle, Program cycle or Erase cycle continues unaffected.

The device identification is assigned by the device manufacturer, and indicates the memory m52p16 in the first byte 20hand the memory capacity of the device in the second byte 15h. Grade 3 is available only in devices delivered in S08N packages. AC characteristics Grade 6 40 Table 1 6.

To spread this overhead, the Page Program PP instruction allows up to bytes to be programmed at a time changing bits from 1 to 0provided that they lie in consecutive addresses on the same page of memory. Absolute maximum ratings Symbol Parameter Min. For a list of available datashheet speed, package, etc.

Instruction set 19 Table 5. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. The designer needs to be aware that if a Power-down occurs while a Write, Program or Erase cycle is in progress, some data corruption can result.

The memory can be programmed 1 to bytes at a time, using the Page Program instruction. This prevents the device from going back to the Hold condition. Most Related.

2SA562 DATASHEET PDF

Micron Tech M25P16-VMN6TP

Chip Select S dtasheet be driven High after the eighth bit of the last data byte has been latched in, otherwise the Page Program PP instruction is not executed. Normally, the device is kept selected, with Chip Select S driven Low, for the whole duration of the Hold condition. If the device was not previously in the Deep Power-down mode, the transition to the Stand-by Power mode is immediate. S01 6 connections 7 Figure 4. It is also possible to read the Status Register continuously, as shown in Figure 1 1. Generally, this capacitor is of the order of nF.

FLEISCHMANN 6852 PDF

M25P16-VMW6P STMicroelectronics, M25P16-VMW6P Datasheet

All the products will packing in anti-staticbag. Ship with ESD antistatic protection. We will inspect all the goods before shipment,ensure all the products at good condition and ensure the parts are new originalmatch datasheet. After all the goods are ensure no problems afterpacking, we will packing safely and send by global express. It exhibitsexcellent puncture and tear resistance along with good seal integrity. Guarantees 1.

Related Articles